10Gbps SFP Active Optical Cable

Cable end connector A	SFP+	Cable end connector B	SFP+
Jumper type	Direct-Attach	Data Rate	10G
Aggregate Bit Rate	10.3125Gbps	Lane Bit Rate	10Gbps
Number of channels	1	Single channel rate	10G
Array transmitter	VSCEL	Array receiver	PIN
Compatible Brands	Cisco/Juniper/Arista/Brocade/H3C/Dell/Extreme/Huawei/Avago/Intel/Mellanox/Mikrotik/Generic	Factory brand	SINOCONEC
Center(Operating)wavelength	850nm	Bit Error Rate	10-12
Fiber type &	OM3 MMF MAX 300m	Cable colour	Aque
Cable material	LSZH	Cable length selection	1-300 meter
Safety certification	TUV/UL/FDA	Application scenarios	10 Gigabit Ethernet (10GbE)
Protocols	SFF-8636/SFF-8431	DDMI	YES
Supply Voltage	3.3V	Power Dissipation	<0.8W
Operating temperature	0 to 70℃ (32 to 158℉)	Storage Temperature	-40 to 85℃ (-40to185℉)

PRODUCTION LINE INTRODUCTION

SINOCONEC has four AOC production lines (including device and package production lines) with a daily AOC production capacity of 2,000. SINOCONEC has the ability to independently design and develop production from passive devices, PCB boards, packaging and testing. We can provide 10-800G various rates of AOC cable products. The company owns CISCO, DELL, ALCATELLUCENT, ARUBA, ARISTA, AVAYA, BROCADE, D-LINK, EXTREME, HP, H3C, HUAWEI, INTEL, JUNIPER, MELLANOX, NETGEAR, TP-LINK and other brand switch test platforms to ensure cable compatibility. SINOCONEC's own device and cable production line fully guarantees product quality, consistency and fast delivery.

PRODUCT PRESENTATION

SINOCONEC SFP+(10G) AOC active optical cable is a directly connected optical fiber assembly with SFP+ connectors, using the multi-mode fiber (MMF) scheme. The product complies with SFF-8431 MSA standard. The more compact structure and fewer components reduce unlimited costs compared to conventional optical module and fiber jumper combinations, and the product is suitable for 10Gbps connections within and between adjacent racks. The optical components in the cable are completely closed to avoid scratching or breakage, greatly improving reliability and reducing maintenance costs.

AOC SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

FEATURES

Electrical interface compliant to SFF-8431						850nm VCSEL laser and PIN photo-detector
Maximum link length of 82m on OM2 MMF and 300m on OM3 MMF						Hot pluggable
Built-in digital diagnostic functions						Operating case temperature 0℃ to 70℃
RoHS compliant (lead free)

APPLICATION

STANDARD COMPLIANCE

ABSOLUTE MAXIMUM RATING

Parameters	Symbol	Min.	Max.	Unit
Power Supply Voltage	VCC	-0.5	+3.6	V
Storage Temperature	TC	40	+85	℃
Relative Humidity	RH	0	85	%

RECOMMENDED OPERATING CONDITIONS

Parameter	Symbol	Min	Typical	Max	Unit
Supply Voltage	VCC	3.15	3.3	3.45	V
Supply Current Per End	lcc	-	-	150	mA
Operating Case Temperature	Tca	0	-	70	℃
Data Rate	DR	-	10.3125	-	Gbps
Fiber Bend Radius	Rb	3	-	-	cm

Notes:

[1]Supply current is shared between VCCTX and VCCRX.

[2]In-rush is defined as current level above steady state current requirements.

TRANSMITTER SPECIFICATIONS

Parameter	Symbol	Min	Typical	Max	Unit
Input Differential Impedance	Rin	-	100	-	Ω
Differential Data Input Swing	Vin	150	-	1200	mv
Transmit Disable Voltage	VD	2.0	-	VCC+0.3	V
Transmit Enable Voltage	Ven	Vee	-	Vee+0.8	V

RECEIVER SPECIFICATIONS

Parameter	Symbol	Min	Typical	Max	Unit
Differential Data Output Swing	Vout	300	-	700	mV
Bit Error Rate	BER	-	-	10-12	-
Output Differential Impedance	Rout	-	100	-	Ω
Loss of Signal-Asserted	-	2	-	VCC+0.3	V
Loss of Signal-Negated	-	Vee	-	Vee+0.8	V

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN DEFINITION

Pin	Symbol	Name/Description
1	VEET [1]	Transmitter Ground
2	TX_FAULT [2]	Transmitter Fault
3	TX_DIS [3]	Transmitter Disable. Laser Output Disabled On High or Open
4	SDA [2]	2-wire Serial Interface Data Line
5	SCL [2]	2-wire Serial Interface Clock Line
6	MOD_ABS [4]	Module Absent. Grounded Within The Module
7	RS0 [5]	Rate Select 0
8	RX_LOS [2]	Loss of Signal Indication. Logico Indicates Normal Operation
9	RS1 [5]	Rate Select 1
10	VEER [1]	Receiver Ground
11	VEER [1]	Receiver Ground
12	RD-	Receiver Inverted DATA Out. Ac Coupled
13	RD+	Receiver DATA Out. Ac Coupled
14	VEER [1]	Receiver Ground
15	VCCR	Receiver Power Supply
16	VCCT	Transmitter Power Supply
17	VEET[1]	Transmitter Ground
18	TD+	Transmitter DATA In. AC Coupled
19	TD-	Transmitter Inverted DATA In. AC Coupled
20	VEET[1]	Transmitter Ground

Notes:

[1] Module circuit ground is isolated from module chassis ground within the module.

[2] Should be pulled up with 4.7KΩ-10KΩ ohms on host board to a voltage between 3.15V and 3.45V.

[3] TX_Disable is an input contact with a 4.7KΩ to10KΩ pullup to VccT inside the module.

[4] Mod_ABS is connected to VeeT or VeeR in the SFP+ module.The host may pull this contact up to Vcc_Host with a resistor in the range 4.7KΩ to10KΩ. Mod_ABS is asserted "High" when the SFP+ module is physically absent from a host slot.

[5] RS0 and RS1are module inputs and are pulled low to VeeT with > 30KΩ resistors in the module.